[Dec-2021] Free NS0-183 Exam Questions NS0-183 Actual Free Exam Questions
Verified NS0-183 dumps and 145 unique questions
NetApp NS0-183 Exam Topics:
| Section | Objectives |
|---|---|
| ONTAP Configuration | - Describe how to use NetApp configurations - Demonstrate knowledge of how a node should be added or replaced |
| ONTAP Networking | - Describe the cluster network, e.g., multi-node, single node clusters - Demonstrate knowledge of the purpose of the management network - Identify the networking components in a cluster environment |
| ONTAP Concepts | - Identify general cluster terms used during installation - Identify ONTAP licensing for 9.7 |
| ONTAP Switches | - Identify the functions of supported switches - Demonstrate knowledge of how to configure/verify configuration requirements |
| Customer Handoff | - Describe how to complete the service report - Demonstrate knowledge of handoff procedures to the customer - Demonstrate knowledge of how to communicate completion and possible problem status - Identify contacts for additional help after handoff |
| Basic Installation Topics and Tools | - Describe installation preparation steps - Describe basic equipment installation steps |
NetApp NS0-183 Exam Certification Details:
| Exam Code | NS0-183 NCSIE |
| Duration | 90 minutes |
| Number of Questions | 60 |
| Exam Name | Storage Installation Engineer ONTAP |
| Recommended Training | ONTAP Clustered Installation Workshop (ILT) ONTAP Cluster Administration (vILT/ILT) Universal FAS Installation (WBT) Introduction to NetApp Installation Standard (WBT) |
| Passing Score | 67% |
| Exam Registration | PEARSON VUE |
| Sample Questions | NetApp NS0-183 Sample Questions |
| Exam Price | $150 USD |
NEW QUESTION 27
An iSCSI LIF fails to migrate during a storage failover test.
In this scenario, why did the LIF not migrate?
- A. LIF failover was not enabled.
- B. The failover policy was not configured.
- C. LIFs that serve block protocols do not failover.
- D. A failover port was not defined.
Answer: C
NEW QUESTION 28
Click the Exhibit button.
You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)
- A. Move the SAS cables to a new stack.
- B. Remove the Ethernet cables.
- C. Disable out-of-band ACP.
- D. Enable in-band ACP.
Answer: A,C
Explanation:
Explanation/Reference:
NEW QUESTION 29
Click the Exhibit button.
A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair.
The switches and the AFF A400 are approximately seven meters apart.
Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)
- A. Install 10 meter NetApp supported copper cables.
- B. Relocate the switches or the AFF A400 so that the distance is less than five meters.
- C. Change the requirement for optical cables.
- D. Change the requirement for Ethernet cables.
Answer: A,D
NEW QUESTION 30
You installed a new AFF A800 2-node ONTAP 9.5 cluster and are asked to run diagnostics to validate the hardware.
Which command is used from the loader prompt to enter diagnostics?
- A. savenv
- B. boot_diags
- C. printenv
- D. sldiag
Answer: B
NEW QUESTION 31
You are installing a pair of Cisco Nexus 3132Q-V cluster switches and receive several syntax errors when the reference configuration file (RCF) is applied.
In this scenario, what are two reasons for these errors? (Choose two.)
- A. Cables were not removed before applying the RCF.
- B. An RCF file for a different version has been loaded.
- C. The switch was not in maintenance mode.
- D. The RCF was already applied.
Answer: B,D
NEW QUESTION 32
In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)
- A. intercluster SnapMirror
- B. Epsilon voting
- C. intracluster SnapMirror
- D. remote cluster peering
- E. cluster database replication
Answer: A,D,E
NEW QUESTION 33
You are installing a 4-node AFF A400 cluster and are asked to create a custom security message before and after user login.
Which two security features are used to perform this task? (Choose two.)
- A. AutoSupport
- B. motd
- C. banner
- D. EMS
Answer: A,C
NEW QUESTION 34
Which statement regarding a node-management LIF is true?
- A. The LIF can be set up on a dedicated VLAN in the data network.
- B. The LIF can be set only on the built-in node-management port - e0M.
- C. The LIF can be set up on a dedicated VLAN in the cluster network.
- D. The LIF must use two switches for redundancy purposes.
Answer: A
NEW QUESTION 35
You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.
In this scenario, what is the minimum number of spare disks required per node and disk type?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 36
While preparing for a new cluster installation, your customer indicates that they have some disk shelves and switches that were discontinued at their old site. They want to re-use as much of this equipment as possible. You must verify that their discontinued equipment is compatible with the new equipment they have on order.
Which two actions will accomplish this task? (Choose two.)
- A. Run the Cluster Configuration Builder tool (ConfigBuilder).
- B. look up the compatibility in the Interoperability Matrix Tool (IMT).
- C. Use the Hardware Universe portal (HWU).
- D. Verify compatibility from Activity IQ.
Answer: B,C
NEW QUESTION 37
You complete a hardware installation on a CN1610 switch and establish a serial connection to the RJ45 port.
In this scenario, the established serial connection allows the installer to complete which two tasks for the switches initial configuration? (Choose two.)
- A. to configure the switch with another CN1610 switch using Cross-Stack EtherChannel configuration for load balancing and performance
- B. to use the serial port connection as a diagnostic channel to the second CN1610 switch in the cluster interconnect
- C. to view network information that has been dynamically assigned to the management interface by the DHCP server on the network
- D. to manually configure the static network information
Answer: C,D
NEW QUESTION 38
Which LIF type is used by default for hardware-assisted storage failover communication?
- A. intercluster
- B. data
- C. cluster-mgmt
- D. node-mgmt
Answer: D
NEW QUESTION 39
Click the Exhibit button.
You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.
Referring to the exhibit, to which port should the redundant management network be cabled?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 40
After completing the installation of a DS224C shelf, you observe the error shown in the exhibit.
Which action should you take to troubleshoot the error? (Choose two.)
- A. Re-seat the IOM module.
- B. Reconnect the SAS cable.
- C. Re-seat the SAS card.
- D. Perform a takeover-giveback.
Answer: A,B
NEW QUESTION 41
In a 4-node cluster, what are two functions of the HA interconnect? (Choose two.)
- A. It provides the ability to migrate a data aggregate to any node in the cluster.
- B. It provides the ability to relocate the aggregate ownership.
- C. It provides the ability to synchronize the cluster configuration.
- D. It provides nondisruptive operations and fault tolerance.
Answer: B,D
NEW QUESTION 42
You have installed and configured a new AFF C190 cluster with ONTAP 9.7. Your customer wants you to install the latest version of ONTAP.
In this scenario, what are two methods to update ONTAP? (Choose two.)
- A. Use ONTAP System Manager to upload and install the new software image.
- B. Use ONTAP System Manager to download and install the new software image.
- C. Use a USB drive with the new software image and let ONTAP automatically boot.
- D. Use the cluster image package get and cluster image update commands.
Answer: B,D
NEW QUESTION 43
Click the Exhibit button.
You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.
Referring to the exhibit, what must you do to solve this problem?
- A. Configure the correct Ethernet ports in all broadcast domains.
- B. Configure the MTU consistently across the cluster.
- C. Configure more than one IPspace.
- D. Configure the LIFs using separate home nodes.
Answer: B
NEW QUESTION 44
You have an AFF A400 cluster that is running ONTAP 9.7 software. You are asked to set up FlexCache for NFS volumes.
In this scenario, which statement is correct when implementing FlexCache?
- A. A subscription license is required.
- B. A site license is required.
- C. No license is required.
- D. A capacity license is required.
Answer: D
NEW QUESTION 45
You are planning the deployment of a new 8-node ONTAP 9.5 cluster. To prepare for the installation, you want to create a custom configuration worksheet with all the information that the customer provided. You also want to use the worksheet to generate CLI commands for your installation.
In this scenario, which NetApp tool will help you achieve your goal?
- A. ConfigBulider
- B. Config Advisor
- C. Config Validator
- D. Fusion
Answer: A
NEW QUESTION 46
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster?
(Choose two.)
- A. FlashCache
- B. FlexClone volumes
- C. thin provisioning
- D. Flash Pool
Answer: A,D
NEW QUESTION 47
You are deploying a cluster with four AFF A300 nodes and Cisco 3232C switches. When you arrive at the customer's site, you notice that there are multiple breakout cables and four Cisco 3232C switches. In this scenario, which statement is true?
- A. A 4-node AFF A300 cluster requires two Cisco 3232C switches for the cluster interconnect and two for management.
- B. Your customer ordered a MetroCluster IP configuration.
- C. A 4-node AFF A300 cluster requires four Cisco 3232C switches.
- D. Cisco best practices require four Cisco 3232C switches for high availability.
Answer: B
NEW QUESTION 48
You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?
- A. Interoperability Matrix Tool (IMT)
- B. Hardware Universe (HWU)
- C. mysupport.netapp.com site
- D. Active IQ Config Advisor
Answer: B
NEW QUESTION 49
You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.
Referring to the exhibit, which steps are required to get an HA cabled system?
- A. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- B. 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.
- C. 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
- D. 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.
Answer: C
NEW QUESTION 50
......
Latest 100% Passing Guarantee - Brilliant NS0-183 Exam Questions PDF: https://www.bootcamppdf.com/NS0-183_exam-dumps.html