Pass Exam With Full Sureness - 156-835 Dumps with 66 Questions
Verified 156-835 dumps Q&As - 100% Pass from BootcampPDF
NEW QUESTION # 16
What is the default Distribution mode?
- A. Network
- B. User
- C. Auto-topology
- D. Manual-General
Answer: C
Explanation:
In Check Point firewall, the default Distribution mode is Auto-topology. Auto-topology uses the built-in algorithm to automatically determine the best way to distribute the traffic across the firewall cluster, based on the topology of the network and the current load on the cluster members.
Auto-topology takes into account the available bandwidth and the CPU utilization of each cluster member, and then makes decisions on how to distribute the traffic across the cluster in real-time. It is a dynamic and adaptive mode that ensures the best use of the available resources and the highest level of performance.
NEW QUESTION # 17
What does the command'g_all' do?
- A. Switches all Appliances to Global mode
- B. It's followed by other command and execute it on all active Appliances within Security Group
- C. Bring up all Appliances
- D. It's followed by other command and execute it on all Appliances connected to Orchestrator
Answer: B
NEW QUESTION # 18
What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?
- A. One Downlink cable only
- B. Three cables: uplink, downlink, SYNC
- C. Two cables: one uplink and one downlink
- D. Four cables: uplink, downlink, SYNC and Management
Answer: A
NEW QUESTION # 19
What is the basic installation sequence of the Orchestrator in case of single Orchestrator?
1. Create a Security Group
2. Configure Default Gateway
3. Connect with Serial Console cable to the Orchestrator
4. Configure IP for one of its Management interfaces
5. Connect an appliance to a downlink port
6. Change Orchestrator amount to 1
7. Browse to the Orchestrator's WebUI
- A. 3-4-2-6-5-7-1
- B. 7-4-2-5-3-1-6
- C. 3-1-7-2-4-6-5
- D. 1-4-2-5-7-3-6
Answer: A
NEW QUESTION # 20
For a VSX configuration - Which statement is wrong?
- A. Each Appliance owns different Virtual Systems
- B. VSX configuration is the same on all Appliances within the same Security Group
- C. All Virtual Systems exist on all Appliances
- D. All Virtual Systems exist on the SMO
Answer: D
NEW QUESTION # 21
There are two appliances within the same Security Group. One of them is connected by One downlink only, another one by Two downlinks. Assuming there's no NAT and no VPN, what would be proportion of traffic distribution done by Orchestrator?
- A. 100%/0%
- B. 66%/33%
- C. 50%/50%
- D. 33%/66%
Answer: C
NEW QUESTION # 22
On MHO-170 - In default configuration, what are GAIA names of Security Group Management ports?
- A. eth1-Mgmt1 and eth1-Mgmt3
- B. eth1-Mgmt1 and eth2-Mgmt1
- C. eth1-Mgmt3 and eth1-Mgmt4
- D. eth1-Mgmt1 and eth1-Mgmt2
Answer: A
NEW QUESTION # 23
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?
- A. Additional ports used as uplinks.
- B. Reserved for internal purposes. Not in use.
- C. 1Gbps connectivity for Security Groups.
- D. Out-of-band interfaces for access to Orchestrator itself.
Answer: D
NEW QUESTION # 24
What is a Security Group?
- A. Group of security gateways
- B. Group of security administrators
- C. Group of appliances with enabled NGTX software blades
- D. Logical group of computer and network resources
Answer: A
NEW QUESTION # 25
What is the Sync network on Appliances used for?
- A. May be used for any purpose, but synchronization always have priority
- B. To transfer configuration files from Orchestrators to Appliances
- C. To transfer data in case of full utilization of the downlink interfaces
- D. To synchronize configurations and connections in between connection tables of different Appliances
Answer: D
NEW QUESTION # 26
One single Appliance supports 1M concurrent connections. How many concurrent connections will support Security Group of 2 Appliances?
- A. 500K
- B. 2M
- C. 4M
- D. 1M
Answer: B
NEW QUESTION # 27
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
- A. Any pair of available ports
- B. This configuration is not supported
- C. Port 1 in Slot 2 and Port 2 in Slot 1
- D. Port 1 in Slot 1 and Port 2 in Slot 1
Answer: D
NEW QUESTION # 28
What will happen in case of NAT of the traffic passing through Management network?
- A. Since Management traffic is always going to SMO, it will take a care for Correction Layer and will re-distribute traffic to other Appliances
- B. Orchestrator will disable NAT and traffic will pass with no issue
- C. This traffic will pass with no inspection
- D. This traffic will not pass correction, since it will be dropped
Answer: D
NEW QUESTION # 29
What is the difference between Dual-Site and Multi-Room?
- A. Multi-Room is a kind of Dual-Site deployment within the same building
- B. Multi-Room is a Single-Site deployment where all Appliances are connected to both orchestrators
- C. This is the same
- D. Multi-Room is Active / Standby and Dual-Site is Active / Active
Answer: A
NEW QUESTION # 30
There are two 10Gbps dual-port NIC installed on a 6800 appliance. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
- A. Any pair of available ports
- B. Port 1 in Slot 1 and Port 1 in Slot 2
- C. Port 1 in Slot 1 and Port 2 in Slot 1
- D. Port 1 in Slot 2 and Port 2 in Slot 1
Answer: B
NEW QUESTION # 31
What is an uplink interface used for?
- A. To connect appliances to customer's infrastructure
- B. To connect in between Orchestrators
- C. To connect in between appliances
- D. To connect Orchestrators to customer's infrastructure
Answer: A
NEW QUESTION # 32
What kinds of transceivers are supported on Orchestrator MHO-140?
- A. SFP+, SFP28, QSFP
- B. SFP, QSFP, QSFP28
- C. SFP, SFP+, QSFP, QSFP28
- D. SFP, SFP+, SFP28
Answer: C
NEW QUESTION # 33
How many power supplies are presented on MHO-170?
- A. 0
- B. 1
- C. 2
- D. 1 with option for 2
Answer: C
NEW QUESTION # 34
What cannot be learned from the output of asg perf -v -p command?
- A. Average CPU usage on Appliances
- B. Per-path distribution
- C. Real-time throughput
- D. Average CPU usage on Orchestrators
Answer: D
NEW QUESTION # 35
What is a downlink interface used for?
- A. To connect in between Orchestrators
- B. To connect appliances to Orchestrators
- C. To connect Orchestrators to customer's infrastructure
- D. To connect appliances to customer's infrastructure
Answer: B
NEW QUESTION # 36
What is the Orchestrator?
- A. Network Switch
- B. None of above
- C. Manager of compute and network resources, load balancer and network switch
- D. Load balancer
Answer: B
NEW QUESTION # 37
What does the lldpctl command do?
- A. Discover orchestrators
- B. Show all devices discovered by LLDP protocol on uplink ports
- C. Show all devices discovered by LLDP protocol on downlink ports
- D. Show all devices discovered by LLDP protocol on all ports
Answer: D
NEW QUESTION # 38
What is the Iterator process?
- A. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure
- B. Iterator is the process that simulates distribution in case of Appliance failure
- C. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery
- D. Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive
Answer: D
Explanation:
Iterator is the process that follows Appliance recovery and simulates what was a distribution if recovered Appliance was alive. The Iterator process runs on the Security Management Server and simulates the distribution of the Security Gateways if the recovered Appliance was alive. This helps ensure that the network remains secure and the traffic flow is optimized.
NEW QUESTION # 39
What cannot be learned from the output of lldpctl?
- A. Serial number of Appliance
- B. Distribution mode
- C. Appliance model
- D. Orchestrator's IP
Answer: B
NEW QUESTION # 40
......
156-835 Dumps Full Questions - Exam Study Guide: https://www.bootcamppdf.com/156-835_exam-dumps.html
Pass 156-835 Exam in First Attempt Guaranteed 2023 Dumps: https://drive.google.com/open?id=1LkrZ7n5KaOcO_IDjtexn6frrgbe_7oyf