Latest Success Metrics For Actual D-PEMX-DY-23 Exam (Updated 138 Questions)
Genuine D-PEMX-DY-23 Exam Dumps Free Demo Valid QA's
NEW QUESTION # 58
Which uplink configuration combination of the Top of the Rack Switch and the MX7000 Management Module is supported?
- A. 100 Mbps (Auto negotiation ON) and Auto negotiation OFF
- B. 100 Mbps (Auto negotiation OFF) and Auto negotiation OFF
- C. 100 Mbps (Auto negotiation OFF) and Auto negotiation ON
Answer: B
NEW QUESTION # 59
Which I/O module is supported for Fabric B?
- A. MX5000s
- B. MSG610s
- C. MX5016s
- D. MX5108n
Answer: D
NEW QUESTION # 60
When performing "A1 the Box" management, what must be done to successfully connect to the Management Module?
- A. Change the baud rate to 128000
- B. Attach standard A-to-A USB cable to a laptop
- C. Connect cables to the KVM
- D. Configure PuTTY for a serial connection
Answer: D
NEW QUESTION # 61
What can be used as the firmware update source for OME-M within an MX chassis?
- A. Server Update Utility
System Live Image (SLI) - B. Dell Update package
System Live Image (SLI) - C. Server Update Utility
Baseline from a Catalog - D. Dell Update Package
Baseline from a Catalog
Answer: D
NEW QUESTION # 62
An MX7000 administrator has been tasked to perform the initial configuration of a new MX platform.
The MX700 has seven MX740c, one MX5016s, two Management Modules (MMs), an LED-Only control panel, two MX9116n in Fabric A, two MX5108n in Fabric B, and two MX5000s in Fabric C.
What is a valid method to perform the initial MX platform configuration?
- A. Use KVM and racadm setniccfg command from MM configuration menu
- B. Use a serial DB9 / DB cable
- C. Use Ethernet front panel port default DHCP address
- D. Use QuickSync 2
Answer: A
NEW QUESTION # 63
What is the connection protocol between FReD and MM?
- A. FC
- B. I2C
- C. HDMI
- D. Ethernet
Answer: B
NEW QUESTION # 64
Which section of the PowerEdge MX7000 chassis provides a structure for mounting PSUs and sleds?
- A. Management Module slot
- B. Rear Tub
- C. Main Chassis
- D. Main Distribution Board
Answer: C
NEW QUESTION # 65
An administrator is mapping the drives of an MX5016s. The disk must be split in groups among multiple compute sled slots.
Which storage configuration must be used?
- A. Drive-Assigned mode
- B. Split-Assigned mode
- C. Enclosure-Assigned mode
Answer: A
NEW QUESTION # 66
What is a characteristic of MX7000 networking in Full Switch Mode?
- A. Networking is enabled by default and all switch-specific OS10EE capabilities are available.
- B. Layer 2 bridging is disabled by default and interfaces must join a bridge domain (VLAN) before being able to forward frames.
- C. Networking is available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
- D. Switches operate as layer 2 I/O aggregation devices and are managed through OME-M.
Answer: A
NEW QUESTION # 67
In SmartFabric mode, what is the recommended maximum number of VLANs per server port on an MX7000 switch?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 68
An administrator is asked to install and power on a new MX740c sled in a PowerEdge MX7000 chassis. The administrator inserts the sled and presses the power button. The power button LED is pulsating green. After a short time, the power button turns to solid green and the server turns on.
What operation was in progress when the power button was pulsating green?
- A. iDRAC was booting
- B. Lifecycle Controller was taking firmware inventory
- C. Management Module was updating its component inventory
- D. IOM was booting
Answer: A
NEW QUESTION # 69
In addition to one compute sled, one management module, and one IOM, what is the minimum required HW configuration on the PowerEdge MX7000 to POST?
- A. 1 power supply unit
2 front cooling fans
3 rear cooling fans - B. 2 power supply units
4 front cooling fans
5 rear cooling fans - C. 1 power supply unit
1 front cooling fan
1 rear cooling fan - D. 3 power supply units
4 front cooling fans
5 rear cooling fans
Answer: B
NEW QUESTION # 70
When multiple MX9002m modules are daisy-chained to Top-of-Rack switches, which uplink port can be used for stacking?
- A. Either uplink port can be utilized
- B. Only the Gb2 port on the primary (left) MX9002
- C. Gb1 uplink ports can only stack with other Gb2 ports
- D. Only the Gb2 port on the secondary (right) MX9002
Answer: A
NEW QUESTION # 71
Which statement describes L2 Multicast as implemented on the PowerEdge MX7000 IOM?
- A. MLD snooping controls the flooding of IPv6 multicast traffic on VLANs while the IGMP limits the flooding of IPv4 multicast traffic.
- B. MLD snooping and IGMP control or limit the flooding of IPv6 multicast traffic on VLANs.
- C. MLD snooping and IGMP control or limit the flooding of IPv4 multicast traffic on VLANs.
- D. MLD snooping controls the flooding of IPv4 multicast traffic on VLANs while the IGMP limits the flooding of IPv6 multicast traffic.
Answer: A
NEW QUESTION # 72
Refer to the exhibit.
What is shown?
- A. MX5016s
- B. MXG610s
- C. MX5000s
- D. MX5108n
Answer: A
NEW QUESTION # 73
On which generation of server was the BOSS-N1 controller introduced?
- A. 15G
- B. 16G
- C. 14G
Answer: B
NEW QUESTION # 74
......
D-PEMX-DY-23 Practice Test Give You First Time Success with 100% Money Back Guarantee!: https://www.bootcamppdf.com/D-PEMX-DY-23_exam-dumps.html